Eager Plastics, inc.
3350 W. 48th Pl Chicago, IL 60632
MATERIAL SAFETY DATA SHEET
- EP 8038 Part B -
PRODUCT NAME: EP 8038 Part B
CHEMICAL TYPE: Extended Polyether Polyol
COMPONENTS: % TLV (ACGIH)
(CAS Unassigned) 52 Not established
High Molecular Weight Plastizer
(CAS 6840-50-0) 45 Not established
APPEARANCE & ODOR: Clear liquid, slightly fruity odor.
BOILING POINT: 536oF
SPECIFIC GRAVITY: .985 at 20oC
VAPOR PRESSURE: 4 mm Hg at 121oC
SOLUBILITY IN WATER: Partial
FLASH POINT: 262oF Pensky-Martens Closed Cup
EXTINGUISHING MEDIA: Dry chemical, carbon dioxide, high expansion (proteinic) chemical foam.
SPECIAL FIRE FIGHTING PROCEDURES: Full emergency equipment with self-contained breathing apparatus and full protective clothing should be worn by firefighters.
UNUSUAL FIRE OR EXPLOSION HAZARDS: Combustible liquid. Containers exposed to intense heat from fires should be cooled with water to prevent vapor pressure buildup which could result in container rupture.
INCOMPATIBILITY (MATERIALS TO AVOID): Oxidizing agents and isocyanates.
HAZARDOUS POLYMERIZATION: Will not occur.
HAZARDOUS DECOMPOSITION PRODUCTS: By high heat and fire: carbon monoxide.
GENERAL: No toxicity information is available on this specific preparation; this health hazard assessment is based on information that is available on the properties of its components.
PRIMARY ROUTE(S) OF ENTRY: Skin; Inhalation
INHALATION: Low hazard for usual industrial handling.
SKIN CONTACT: Low hazard for usual industrial handling.
EYE CONTACT: Liquid is minimally irritating to the eyes.
INGESTION: Ingestion may result in gastric upset.
CARCINOGENICITY: None of the ingredients are listed by NTP, IARC, or regulated by OSHA as a carcinogen.
FIRST AID PROCEDURES:
Skin: Wash material off skin with plenty of soap and water. Seek medical attention if irritation develops or persists after the area is washed. Do not reuse clothing until cleaned.
Eyes: Flush with copious amounts of water for at least 15 minutes holding eyelids open. Refer individual to medical attention for immediate follow-up.
Ingestion: If ingested, consult physician.
Inhalation: Move to area free of risk to further exposure. Administer oxygen or artificial respiration as needed. Get medical attention.
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Remove all possible ignition sources.
Major Spill: Large quantities may be pumped into storage/salvage vessels.
Minor Spill: Absorb material with sawdust or other absorbent, shovel into suitable containers for proper disposal.
Clean-up: Flush area with water to remove trace residue.
WASTE DISPOSAL METHOD: Waste must be disposed of according to federal, state and local environmental control regulations. Decontaminate containers prior to disposal. Empty containers should be crushed to prevent reuse. DO NOT HEAT OR CUT EMPTY CONTAINER WITH ELECTRIC OR GAS TORCH.
TLV OR SUGGESTED CONTROL VALUE: No ACGIH TLV or OSHA PEL is assigned to this mixture. Minimize exposure in accordance with good hygiene practice.
EYE PROTECTION: Liquid chemical goggles or full face shield.
SKIN PROTECTION: Chemical resistant gloves recommended.
RESPIRATORY PROTECTION: If respiratory protection is needed, use MSHA/NIOSH approved respirator for organic vapor.
VENTILATION: Local exhaust should be sufficient to control airborne levels.
OTHER PROTECTIVE EQUIPMENT: None.
Store in tightly sealed containers to protect from atmospheric moisture. Educate and train employees in safe use of product.
TSCA (Toxic Substances Control Act) Regulations, 40 CFR 710:
All ingredients are on the TSCA 8(b) Inventory.
CERCLA and SARA Regulations (40 CFR 355,370, and 372):
313 Supplier Notification. This product contains the following toxic chemicals subject to reporting requirements of 313 of the Emergency Planning and Community Right-To-Know Act of 1986 and of 40 CFR 372: None
California Proposition 65: No warnings are necessary
DOT Classification: Not regulated
Date prepared: 2/98