Section 1 - Chemical Product and Company Identification                      

Product/Chemical Name: Ease Release 2310           Date Prepared: 7/21/98

General Use: Mold Release Agent

From: Eager Plastics, Inc. 3350 W. 48th Pl. Chicago, IL 60632. 773-927-3484

Emergency Contact: 773-807-4314

Back to our homepage at: www.eagerplastics.com

 

Section 2 - Composition / Information on Ingredients

Component

CAS Number

ACGIH TLV

Exposure Limits

 OSHA PEL

Weight Percent

(%)

Other

Petroleum Solvent

64741-66-8

None Established

None Established

80-90

400 ppm

Isopropyl Alcohol

67-63-0

400 ppm

400 ppm

5-10

 

Salts of Fatty Acids

Mixture

None Established

None Established

3-6

 

Section 3 - Hazards Identification

 

Potential Health Effects Potential Health Effects

HMIS

H

F

R

231

 

 

 

 
 


Acute Effects Inhalation: Over exposure by inhalation of vapors may cause respiratory irritation or nonspecific discomfort such as nausea, headache or weakness.  Inhalation of concentrations above the recommended limits may cause temporary central nervous system depression with anesthetic effects such as dizziness, headache, incoordination and loss of consciousness.  Gross overexposure may be fatal.  Inhalation of respirable aerosols of the release agent in this product may cause serious toxic effect in the lungs, based on animal studies.

Eye: Eye contact with liquid or vapor may cause irritation.

Skin:  Skin contact with the liquid may cause freezing of the skin or irritation.

Ingestion: Ingestion is not considered a potential route of exposure

Carcinogenicity: This product contains no components listed as carcinogenic by IARC, NTP, and OSHA 1910(Z).

Medical Conditions Aggravated by Long-Term Exposure: 

Individuals with preexisting diseases of the central nervous or cardiovascular system may have increased susceptibility to the toxicity of excessive exposure.

Chronic Effects: No chronic health effects known.

 

Section 4 - First Aid Measures

 

Inhalation:        Remove source(s) of contamination and move victim to fresh air.  If breathing has stopped, give artificial                                    respiration, then oxygen if needed.  Contact physician immediately. 

Eye Contact:     Flush eyes with plenty of water. If irritation persists, seek medical attention.

Skin Contact: In case of skin contact, wash thoroughly with soap and water.

Ingestion:          Ingestion is unlikely route of exposure.  Do not induce vomiting unless instructed by a physician.

After first aid, get appropriate in-plant, paramedic, or community medical support.

Note to Physicians:

 Because of possible disturbance of cardiac rhythm, catecholamine drugs, such as epinephrine, should be used only in situations of emergency life support.

 

 

 

 

 

 

 

Section 5 - Fire-Fighting Measures

 

 
FlashPoint: >19°F (-7°C)

Flammable Limits:     LEL:  1.5    Note: Approximate

                                    UEL:  11.6

Flash Point Method: TCC

Autoignition Temperature:  750°F (400°C)   Note: Approximate

Flammability Classification: Flammable Liquid

General Hazard:  Material will readily ignite at ambient temperatures.  Material can accumulate static charges which can cause an incendiary electrical discharge.  “Empty” containers retain product residue (liquid and/or vapor) and can be dangerous.  DO NOT Pressurize, cut, weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks, static electricity, or other sources of ignition;  They may explode and cause injury or death. Empty drums should be completely drained, properly bunged and promptly returned to a drum reconditioner, or properly disposed of.

Extinguishing Media: Water Fog, Dry Chemical, and Carbon Dioxide Foam

Unusual Fire or Explosion Hazards: None

Fire-Fighting Instructions:       Use water spray to cool fire exposed surfaces and to protect personnel.  Shut off “fuel” to fire. If a leak or spill has not ignited, use water spray to disperse the vapors.  Either allow fire to burn under controlled conditions or extinguish with foam or dry chemical.  Try to cover liquid spills with foam.  Avoid spraying water directly onto storage containers due to danger of boilover.  This liquid is volatile and gives off invisible vapors.  Either the liquid or vapor may settle in low areas or travel some distance along the ground or surface to ignition sources where they may ignite or explode.

Section 6 - Accidental Release Measures

Spill /Leak Procedures: Avoid breathing vapors.  Evacuate area until vapor has been dispersed.  Remove all sources of ignition.  Stop or reduce discharge if it can be done safely.

Section 7 - Handling and Storage

Handling Precautions: Minimize breathing of vapors and avoid prolonged or repeated contact with skin.  Wear proper protective equipment.  If ventilation is not sufficient, wear proper respiratory equipment.  Do not use near ignition sources. 

Storage Requirements: Store in cool dry, well-ventilated area away from all sources of ignition.  “Empty” containers retain product residue (liquid and/or vapor) and can be dangerous.  Do not Pressurize, cut, weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks, static electricity, or other sources of ignition;  They may explode and cause injury or death. Empty drums should be completely drained, properly bunged and promptly returned to a drum reconditioner, or properly disposed of.

Section 8 - Exposure Controls / Personal Protection

Engineering Controls:

Ventilation: Provide general or local exhaust ventilation systems to maintain airborne concentrations below OSHA PELs (Sec. 2). Local exhaust ventilation is preferred because it prevents contaminant dispersion into the work area by controlling it at its source.

Administrative Controls:

Respiratory Protection: Seek professional advice prior to respirator selection and use. Follow OSHA respirator regulations (29 CFR 1910.134) and, if necessary, wear an MSHA/NIOSH-approved respirator. Select respirator based on its suitability to provide adequate worker protection for given working conditions, level of airborne contamination, and presence of sufficient oxygen. For emergency or nonroutine operations (cleaning spills, reactor vessels, or storage tanks), wear an SCBA. Warning! Air-purifying respirators do not protect workers in oxygen-deficient atmospheres. If respirators are used, OSHA requires a written respiratory protection program that includes at least: medical certification, training, fit testing, periodic environmental monitoring, maintenance, inspection, cleaning, and convenient, sanitary storage areas.

Protective Clothing/Equipment: Wear chemically protective gloves, boots, aprons, and gauntlets to prevent prolonged or repeated skin contact. Wear protective eyeglasses or chemical safety goggles, per OSHA eye- and face-protection regulations (29 CFR 1910.133). Contact lenses are not eye protective devices. Appropriate eye protection must be worn instead of, or in conjunction with contact lenses.

Safety Stations: Make emergency eyewash stations, safety/quick-drench showers, and washing facilities available in work area.

Contaminated Equipment: Separate contaminated work clothes from street clothes. Launder before reuse. Remove this material from your shoes and clean personal protective equipment.

Comments: Never eat, drink, or smoke in work areas. Practice good personal hygiene after using this material, especially before eating, drinking, smoking, using the toilet, or applying cosmetics.

Section 9 - Physical and Chemical Properties

Product Form:                        Liquid

Appearance and Odor:          Clear, Slight ethereal odor

Vapor Pressure:                    ~63mm @ 68°F (20°C)

Specific Gravity:                    0.72 

 

Vapor Density (Air=1):        ~4

Water Solubility:                  insoluble

Boiling Point:                        205°-255°F (96°-107°C)

Evaporation Rate:                  (butyl acetate =1)  ~5.6

 

 

 

Section 10 - Stability and Reactivity

Stability: This product is stable at room temperature in closed containers under normal storage and handling conditions.

Polymerization: Hazardous polymerization cannot occur.

Hazardous Decomposition Products: Thermal oxidative decomposition can produce carbon monoxide and carbon dioxide.

 

Section 11- Toxicological Information

None established

Section 12 - Ecological Information

None Established

Section 13 - Disposal Considerations

Disposal: Contact your supplier or a licensed contractor for detailed recommendations. Follow applicable Federal, state, and local regulations.

Section 14 - Transport Information

 

DOT

IATA

IMDG

Shipping Name:  

Petroleum Distillate N.O.S.

(Naphtha Solvent)

UN #: 1268

Hazard Class: 3

Packing Group:  II

 

 

Shipping Name:  

Petroleum Distillate N.O.S.

(Naphtha Solvent)

UN #: 1268

Hazard Class: 3

Packing Group:  II

 

 

Shipping Name:  

Petroleum Distillate N.O.S.

(Naphtha Solvent)

UN #: 1268

Hazard Class: 3

Packing Group:  II

 

 

 

Section 15 - Regulatory Information

EPA Regulations:

SARA 311/312 Codes: 

                This product contains the following chemicals that are subject to release reporting requirements under section 313 of                 SARA Title III.  None

                         

Section 16 - Other Information

Prepared By:      Timothy C. Boyer

Title:                    Chemist

 

The information contained in this MSDS is considered accurate as of the version date.  However, no warranty is expressed or implied regarding the accuracy of the data.  Since the use of this product is not within the control of Mann Formulated Products, a subsidiary of Smooth-On Inc., it is the user’s obligation to determine the suitability of the product for its intended application and assumes all risk and liability for its safe use.